Where to buy
Fill the form to download the product manual

Account settings

[s2Member-Profile /]

Software Release Highlights / Notes

Release Summary

Version: S5
  • endpoints I2&I3 disabled by default
  • improvement of bistable switch functionality
  • serial number support
Version: S4
  • improvement of reporting to controller, assoc. 1
Version: S3
  • Increased imunity (long wires) on digital inputs

Release Summary

Version: S4
  • changed PN
  • changed manufacturer info
  • changed version
  • parameters 100 and 101 set to 9 when module reported value system instead of home security
  • removed 10% switch multilevel report
  • by default endpoints are disabled
  • fixed output state with bistabel switch after power cycle
  • fixed dimming duration when start level change is sent
Version: S3
  • reporting on 0,1kwh delta
  • secure/unsecure parameter selection (par.250)
  • autoinclusion time changed to 2min.
  • overload protection, if power is exceeding max. value for time >5s output switch off automatically
  • overload notification
Version: S2
  • endpoints I2&I3 disabled by default
  • serial number support

Release Summary

Version: S6
  • Unsecure/secure inclusion (parameter no.250)
  • changed default values
  • Parameter no. 76 = 30 = 30W
  • Parameter no 85 = 30 = 3s
  • Parameter no. 40 = 10 = 10%
  • Parameter no. 42 = 0 = reporting disabled
Version: S5
  • support for “serial number”
Version: S4
  • increased imunity (long wires) on digital inputs
  • improvement of reporting to controller, assoc. 1
Version: S3
  • improvement of slats tilt positioning

Release Summary

Version: S5
  • New parameter No. 76 reporting on time interval
  • New parameter No. 77 reporting delay
  • New parameter No. 78 scale selection
  • New association group 10 same as association group 2 but with delay
  • Small fxes (temperature reporting, association get, meter report)
Version: S2
  • Temp sensor selector (internal/external) added
  • max. load power limitation added

Release Summary

Version: S5
  • New parameter No. 76 reporting on time interval
  • New parameter No. 77 reporting delay
  • New parameter No. 78 scale selection
  • New association group 10 same as association group 2 but with delay
  • Small fxes(temperature reporting, association get, meter report)
Version: S4
  • part number change
  • device ID fix
  • fix in power reporting on change – it didn’t report multichannel encapsulated
Version: S3
  • precision 2 – set values greater than 32 deg
  • notification from e2, e3 when chosen but not enabled 100,101 enable
  • association 4 – extended functionality: (triggered when actual temperature reach Too high or Too Low temperature limit)
  • parameter to_low, to_high temperature has no influence on set value to setpoint
  • Fahrenheit fix
Version: S2
  • serial number support
  • improvement of window sensor impact to temperature regulation
  • improvement of condense sensor impact to temperature regulation
  • support for class meter V4

Release Summary

Version: S5
  • New parameter no. 76 reporting on time interval
  • New parameter no. 77 reporting delay
  • New parameter no.78  scale selection
  • New association group 10 like association group 2 but with delay
  • Small fxes (temperature reporting, association get, meter report)
Version: S2
  • Temp sensor selector (internal/external) added
  • max. load power limitation added

Release Summary

Version: S4
  • endpoints I2 disabled by default
  • improvement of bistable switch functionality
  • serial number support
Version: S3
  • temperature presented as separate endpoint
Version: S2
  • Increased immunity (long wires) on digital inputs

Release Summary

Version: S5
  • support for “serial number”
Version: S4
  • improvement of reporting to controller, assoc. 1
Version: S3
  • improvement of slats tilt positioning

Release Summary

Version: S2
  • on/off + Dimmer mode added par.5

Release Summary

Version: S6
  • Improved filter on current and watts reporting
Version: S5
  • update on meter reporting
Version: S4
  • serial number support
Version: S3
  • OTA FW update supported

Qubino Use Case Manual